Configuration file of ZTE ZXA10 MDU ONU F820 Data Service-ZTE

***Configuration file of ZTE ZXA10 MDU ONU F820 Data Service***

****Query card status****

OLT-1#show card

****Enter global configuration mode and configure GPON SN****

OLT-1#configure terminal

OLT-1(config)#pon sn ZTEG9000002B

OLT-1(config)#exit

****Reset GPON card (GPUA card) in slot 2 and wait for 1 minute****

OLT-1#reset-card slotno 2

Confirm to reset card?[yes/no]:y

****Enter VLAN interface configuration mode, configure in-band NM IP address****

OLT-1#configure terminal

OLT-1(config)#interface inband-vlan1000

OLT-1(config-if)#ip address 10.67.1.11 255.255.255.0

OLT-1(config-if)#exit

 IMPORTANT:

VLAN 1 – VLAN 4093 are created by default.

⇒ The in-band NM IP address should be in the same network segment with the ZXA10 C220.

****Configure in-band NM route****

OLT-1(config)#ip route 0.0.0.0 0.0.0.0 10.67.1.254

****Configure service VLAN on the F820****

—Configure VLAN service port—

OLT-1(config)#interface fei_0/1/1

OLT-1(config-if)#switchport default vlan 100

OLT-1(config-if)#end

IMPORTANT:

By default, VLAN 1 – VLAN 4093 exist in F820 and the uplink GPON port is each VLAN.

****Save configuration data****

OLT-1#write

IMPORTANT:

⇒ On the ZXA10 C220, the default ONU type of F820 is EPON ONU. To discriminate the ONU types, configure a GPON ONU type, for example, ZTEG-F820.

****Enter the global configuration mode****

OLT-1#configure terminal

****Enter PON configuration mode and configure ONU type****

OLT-1(config)#pon

OLT-1(config-pon)#onu-type ZTEG-F820 gpon

IMPORTANT:

⇒ By default, the ONU type of the F820 is an EPON ONU on the ZXA10 C220. To discriminate the GPON ONU from the EPON ONU, configure a GPON ONU type, such as ZTEG-F820.

****Configure ONU port type****

OLT-1(config-pon)#onu-type-if ZTEG-F820 eth_0/1-24

OLT-1(config-pon)#exit

****Query unconfigured ONU on the GPON-OLT port****

OLT-1(config)#show gpon onu uncfg gpon-olt_0/5/1

****Enter the GPON-OLT interface configuration mode****

OLT-1(config)#interface gpon-olt_0/5/1

OLT-1(config-if)#exit

****Register ONU****

OLT-1(config-if)#register 1 type ZTEG-F820 sn ZTEG9000002B state ready

****Query ONU state****

OLT-1(config-if)#show gpon onu state gpon-olt_0/5/1

OLT-1(config-if)#exit

****Enter the GPON configuration mode****

OLT-1(config)#gpon

OLT-1(config-gpon)#

****Configure bandwidth profile****

OLT-1(config-gpon)#bandwidth-profile T1-50M type 4 maximum 50000

OLT-1(config-gpon)#exit

****Enter the GPON-ONU interface configuration mode****

OLT-1(config)#interface gpon-onu_0/5/1:1

OLT-1(config-if)#

****Create T-CONT****

OLT-1(config-if)#tcont 1 name Tcont50M traffic T1-50M

****Create GEM ports****

OLT-1(config-if)#gemport 1 name NMport unicast tcont 1

OLT-1(config-if)#gemport 2 name Gemport2 unicast tcont 1

OLT-1(config-if)#exit

****Enter the GPON-ONU interface configuration mode****

OLT-1(config)#interface gpon-onu_0/5/1:1

OLT-1(config-if)#

****Configure port mode to hybrid****

OLT-1(config-if)#switchport mode hybrid vport 1

OLT-1(config-if)#switchport mode hybrid vport 2

IMPORTANT:

⇒ By default, one V-port corresponds to one GEM port.

****Add port to in-band NM and service VLAN in tag mode****

OLT-1(config-if)#switchport vlan 1000 tag vport 1

OLT-1(config-if)#switchport vlan 100 tag vport 2

OLT-1(config-if)#exit

IMPORTANT:

⇒ When a port is added to a VLAN, the VLAN is added automatically.

****Enter the OLT uplink port configuration mode****

OLT-1(config)#interface gei_0/14/1

****Configure uplink port mode to hybrid****

OLT-1(config-if)#switchport mode hybrid

****Add uplink port to service VLAN in tag mode****

OLT-1(config-if)#switchport vlan 100 tag

OLT-1(config-if)#exit

****Enter the ONU remote management mode****

OLT-1(config)#pon-onu-mng gpon-onu_0/5/1:1

OLT-1(gpon-onu-mng)#

****Configure the map between GEM port and uplink interface****

OLT-1(gpon-onu-mng)#interwork gemport NMport dot1p-bridge uplink_0/1/1 prio-list 1

****Configure VLAN filter mode on uplink interface****

OLT-1(gpon-onu-mng)# vlan-filter-mode uplink uplink_0/1/1 tagfilter vid-filter untag-filter discard

****Configure VLAN filter entry on uplink interface****

OLT-1(gpon-onu-mng)#vlan-filter uplink uplink_0/1/1 priority 1 vid 1000

****Configure the map between GEM port and uplink interface****

OLT-1(gpon-onu-mng)#interwork gemport Gemport2 dot1p-bridge uplink_0/1/2 prio-list 1

**** Configure VLAN filter mode on uplink interface****

OLT-1(gpon-onu-mng)# vlan-filter-mode uplink uplink_0/1/2 tagfilter vid-filter untag-filter discard

**** Configure VLAN filter entry on uplink interface****

OLT-1(gpon-onu-mng)#vlan-filter uplink uplink_0/1/2 priority 1 vid 100

**** Save configuration data****

OLT-1#write

Configuration Procedure>>

***END***

Be the first to comment

Leave a Reply

Your email address will not be published.


*


For security, use of Google's reCAPTCHA service is required which is subject to the Google Privacy Policy and Terms of Use.

I agree to these terms.