Configuration of Link Aggregation in Static LACP Mode>HUAWEI-Switch

gpontutorials.com-Link Aggregation in Static LACP Mode
gpontutorials.com-Link Aggregation in Static LACP Mode

**Configuration of Link Aggregation in Static LACP Mode**

Configuration Steps: 

  1. Create an Eth-Trunk numbered one and configure Eth-Trunk 1 to work in static LACP mode.# Configure S-switch-A.
    <Quidway> system-view
    [Quidway] sysname S-switch-A
    [S-switch-A] interface eth-trunk 1
    [S-switch-A-Eth-Trunk1] mode lacp-static
    [S-switch-A-Eth-Trunk1] quit

    # Configure S-switch-B.

    <Quidway> system-view
    [Quidway] sysname S-switch-B
    [S-switch-B] interface eth-trunk 1
    [S-switch-B-Eth-Trunk1] mode lacp-static
    [S-switch-B-Eth-Trunk1] quit
  2. Add member interfaces to the Eth-Trunk.# Configure S-switch-A.
    [S-switch-A] interface GigabitEthernet 0/0/1
    [S-switch-A-GigabitEthernet0/0/1] eth-trunk 1
    [S-switch-A-GigabitEthernet0/0/1] quit
    [S-switch-A] interface GigabitEthernet 0/0/2
    [S-switch-A-GigabitEthernet0/0/2] eth-trunk 1
    [S-switch-A-GigabitEthernet0/0/2] quit
    [S-switch-A] interface GigabitEthernet 0/0/3
    [S-switch-A-GigabitEthernet0/0/3] eth-trunk 1
    [S-switch-A-GigabitEthernet0/0/3] quit

    # Configure S-switch-B.

    [S-switch-B] interface GigabitEthernet 0/0/1
    [S-switch-B-GigabitEthernet0/0/1] eth-trunk 1
    [S-switch-B-GigabitEthernet0/0/1] quit
    [S-switch-B] interface GigabitEthernet 0/0/2
    [S-switch-B-GigabitEthernet0/0/2] eth-trunk 1
    [S-switch-B-GigabitEthernet0/0/2] quit
    [S-switch-B] interface GigabitEthernet 0/0/3
    [S-switch-B-GigabitEthernet0/0/3] eth-trunk 1
    [S-switch-B-GigabitEthernet0/0/3] quit
  3. Configure the Eth-Trunk to process BPDUs.# Configure S-switch-A.
    [S-switch-A] interface eth-trunk 1
    [S-switch-A-Eth-Trunk1] bpdu enable
    [S-switch-A-Eth-Trunk1] quit

    # Configure S-switch-B.

    [S-switch-B] interface eth-trunk 1
    [S-switch-B-Eth-Trunk1] bpdu enable
    [S-switch-B-Eth-Trunk1] quit
  4. On S-switch-A, set the LACP priority of the system to 100 so that S-switch-A becomes the Actor.
    [S-switch-A] lacp priority 100
  5. On S-switch-A, set upper threshold M for the number of active interfaces to 2.
    [S-switch-A] interface eth-trunk 1
    [S-switch-A-Eth-Trunk1] max bandwidth-affected-linknumber 2
    [S-switch-A-Eth-Trunk1] quit
  6. On S-switch-A, set the LACP priority of the interface and determine active links.
    [S-switch-A] interface GigabitEthernet 0/0/1
    [S-switch-A-GigabitEthernet0/0/1] lacp priority 100
    [S-switch-A-GigabitEthernet0/0/1] quit
    [S-switch-A] interface GigabitEthernet 0/0/2
    [S-switch-A-GigabitEthernet0/0/2] lacp priority 100
    [S-switch-A-GigabitEthernet0/0/2] quit
  7. Verify the configuration.

    # Check the information about the Eth-Trunks of the S-switchs and check whether the negotiation succeeds on the link.

    [S-switch-A] display eth-trunk 1
    [S-switch-B] display eth-trunk 1
                                      
                                        ***END***

 

1 Comment

  1. Needed to create you a very small observation to help give many thanks again on the pleasant tactics you’ve shown at this time. This has been really unbelievably generous with people like you giving unreservedly exactly what many individuals would have offered for sale for an electronic book to end up making some money for their own end, certainly considering the fact that you might well have done it in case you considered necessary. These points as well served as a good way to comprehend other individuals have similar dreams the same as my own to learn good deal more when it comes to this issue. I’m sure there are lots of more pleasurable occasions in the future for individuals who examine your blog post.

Leave a Reply

Your email address will not be published.


*