Configuration of the IPv6 Services in the FTTB/C Scenario-HUAWEI

gpontutorials.com-IPv6 Services in the FTTB-C (No HGWs) Scenario
gpontutorials.com-IPv6 Services in the FTTB-C (No HGWs) Scenario

***Configuring IPv6 Services in the FTTB/C (No HGWs) Scenario***

Step-1: Configure GPON ONU profiles.

  1. Configure a DBA profile.

OLT-1(config)#dba-profile add profile-name fttb_dba type3 assure 8192 max 20480

  1. Configure an ONU line profile.

OLT-1(config)#ont-lineprofile gpon profile-id 10 profile-name fttb(c)

OLT-1(config-gpon-lineprofile-10)#tcont 4 dba-profile-name fttb_dba

OLT-1(config-gpon-lineprofile-10)#gem add 11 eth tcont 4 cascade on

OLT-1(config-gpon-lineprofile-10)#gem add 12 eth tcont 4 cascade on

OLT-1(config-gpon-lineprofile-10)#gem add 13 eth tcont 4 cascade on

OLT-1(config-gpon-lineprofile-10)#gem mapping 11 0 vlan 8

OLT-1(config-gpon-lineprofile-10)#gem mapping 12 1 vlan 1001

OLT-1(config-gpon-lineprofile-10)#gem mapping 13 2 vlan 200

OLT-1(config-gpon-lineprofile-10)#commit

OLT-1(config-gpon-lineprofile-10)#quit

Step-2: Add an ONU to an OLT.

Assume that the ID of GPON port 0/2/1 is 1, SN is 44305671B39FD656, management mode is SNMP, and the bound line profile is fttb(c). Connect the ONU to such a GPON port through the optical splitter. There are two modes to add an ONT: add an ONT offline and confirm an automatically discovered ONU.

=>Add an ONU offline.

OLT-1(config)#interface gpon 0/2

OLT-1(config-if-gpon-0/2)#ont add 1 ontid 1 sn-auth 44305671B39FD656 snmp ont-lineprofile-name fttb(c)

=>Confirm an automatically discovered ONU.

OLT-1(config)#interface gpon 0/2

OLT-1(config-if-gpon-0/2)#port 1 ont-auto-find enable

OLT-1(config-if-gpon-0/2)#display ont autofind 1

OLT-1(config-if-gpon-0/2)#ont confirm 1 ontid 1 sn-auth 44305671B39FD656 snmp ont-lineprofile-name fttb(c)

Step-3: Check the ONU status.

After an ONU is added, run the display ont info command to query the current status of the ONU. Ensure that Config flag of the ONU is active, Run State is online, and Config state is normal.

OLT-1(config-if-gpon-0/2)#display ont info 1 1

OLT-1(config-if-gpon-0/2)#quit

Step-4: Configure the inband management VLAN and IP address of the OLT.

OLT-1(config)#vlan 8 smart

OLT-1(config)#port vlan 8 0/19 0

OLT-1(config)#vlan priority 8 6

OLT-1(config)#interface vlanif 8

OLT-1(config-if-vlanif8)#ip address 192.168.50.1 24

OLT-1(config-if-vlanif8)#quit

Step-5: Configure the inband management VLAN and IP address of the ONU.

OLT-1(config)#interface gpon 0/2

OLT-1(config-if-gpon-0/2)#ont ipconfig 1 1 static ip-address 192.168.50.2 mask 255.255.255.0 gateway 192.168.50.1 vlan 8

OLT-1(config-if-gpon-0/2)#quit

Step-6: Configure an inband management service port.

OLT-1(config)#service-port 1 vlan 8 gpon 0/2/1 ont 1 gemport 11 multi-service user-vlan 8 rx-cttr 6 tx-cttr 6

Step-7: Confirm that the management channel between the OLT and the ONU is available.

=>On the OLT, run the ping 192.168.50.2 command to check the connectivity between the OLT and the ONU. The ICMP ECHO-REPLY packet from the ONU should be received.

=>On the OLT, you can remote log in to the ONU to perform the configuration.

Step-8: Configure the channel for the Internet access service.

OLT-1(config)#vlan 100 smart

OLT-1(config)#vlan attrib 100 stacking

OLT-1(config)#port vlan 100 0/19 0

OLT-1(config)#service-port 101 vlan 100 gpon 0/2/1 ont 1 gemport 12 multiservice user-vlan 1001 tag-transform translate-and-add inner-vlan 258 rx-cttr 6 tx-cttr 6

 Step-9: Configure the channel for the VoIP service.

OLT-1(config)#vlan 200 smart

OLT-1(config)#port vlan 200 0/19 0

OLT-1(config)#traffic table ip index 9 cir off priority 5 priority-policy localsetting

OLT-1(config)#service-port 201 vlan 200 gpon 0/2/1 ont 1 gemport 13 multiservice user-vlan 200 rx-cttr 9 tx-cttr 9

 Step-10: Configure LAG for upstream ports.

Configure upstream ports 0/19/0 and 0/19/1 into an aggregation group. Each member port in the aggregation group allocates packets based on the source MAC address. The working mode is LACP static aggregation.

OLT-1(config)#link-aggregation 0/19 0-1 ingress workmode lacp-static

Step-11: (Optional) When PPPoE is adopted, enable forwarding the packets with PITP tag on the OLT equipment.

OLT-1(config)#pitp permit-forwarding service-port 101 enable

Step-12: (Optional) When IPoE is adopted, enable forwarding the packets with DHCP option on the OLT equipment.

OLT-1(config)#dhcp-option82 permit-forwarding service-port 101 enable

OLT-1(config)#dhcpv6-option permit-forwarding port 0/2/1 ontid 1 enable

Step-13: Save the configuration data on the OLT.

OLT-1(config)#save

 Step-14: Log in to and configure the ONU.

You can remote log in to the ONU from the OLT to perform the configuration. By default, the user name is root and the password is mduadmin.

NOTE:

The following steps are configured on the ONU side.

Step-15: Configuration the HSI service on the ONU side.

NOTE:

This example creates one service port as an example. Each service port maps a user. When configuring another service port, map the corresponding SVLAN.

OLT-1(config)#vlan 1001-1016 smart

OLT-1(config)#port vlan 1001-1016 0/0 1

OLT-1(config)#traffic table ip index 8 cir 4096 priority 0 priority-policy local-Setting

 OLT-1(config)#service-port 101 vlan 1001 eth 0/3/1 multi-service user-vlan untagged rx-cttr 8 tx-cttr 8

Step-16: (Optional) Configure the PITP function for PPPoE.

OLT-1(config)#raio-mode common pitp-pmode

OLT-1(config)#pitp enable pmode

 Step-17: Configure the DHCP option function for IPoE.

OLT-1(config)#raio-mode common dhcp-option82 //For DHCPv4 packets

OLT-1(config)#dhcp option82 enable //For DHCPv4 packets

OLT-1(config)#raio-mode common dhcpv6-option //For DHCPv6 packets

OLT-1(config)#dhcpv6 option enable //For DHCPv6 packets

Step-18: Configure the voice service.

OLT-1(config)#vlan 200 smart

OLT-1(config)#port vlan 200 0/0 1

OLT-1(config)#interface vlanif 200

OLT-1(config-if-vlanif200)#ip address 17.10.10.10 24

OLT-1(config-if-vlanif200)#quit

OLT-1(config)#voip

OLT-1(config-voip)#ip address media 17.10.10.10 17.10.10.1

OLT-1(config-voip)#ip address signaling 17.10.10.10

OLT-1(config-voip)#quit

OLT-1(config)#ip route-static 200.200.200.0 24 17.10.10.1

OLT-1(config)#interface h248 0

 Are you sure to add MG interface?(y/n)[n]:y

OLT-1(config-if-h248-0)#if-h248 attribute mgip 17.10.10.10 mgport 2944 code text transfer udp primary-mgc-ip1 200.200.200.200 primary-mgc-port 2944 mg-media-ip1 17.10.10.10 start-negotiate-version 1

OLT-1(config-if-h248-0)#reset coldstart

Are you sure to reset MG interface?(y/n)[n]:y

OLT-1(config-if-h248-0)#quit

OLT-1(config)#esl user

OLT-1(config-esl-user)#mgpstnuser batadd 0/3/0 0/3/23 0 terminalid 0 telno 83110001

OLT-1(config-esl-user)#mgpstnuser modify 0/3/0 priority cat2

OLT-1(config-esl-user)#quit

OLT-1(config)#pstnport

OLT-1(config-pstnport)#pstnport attribute batset 0/3/0 0/3/23 reverse-pole-pulse enable

OLT-1(config-pstnport)#quit

 Step-19: Save the configuration on the ONU side.

OLT-1(config)#save

***END***

Be the first to comment

Leave a Reply

Your email address will not be published.


*


For security, use of Google's reCAPTCHA service is required which is subject to the Google Privacy Policy and Terms of Use.

I agree to these terms.