Configuration of the IPv6 Services in the FTTB with HGW Scenario-HUAWEI

gpontutorials.com-IPv6 Services in the FTTB+HGW Scenario
gpontutorials.com-IPv6 Services in the FTTB+HGW Scenario

***Configuring IPv6 Services in the FTTB+HGW Scenario***

Step-1: Configure GPON ONU profiles.

  1. Configure a DBA profile.

OLT-1(config)#dba-profile add profile-name fttb_dba type3 assure 8192 max 20480

  1. Configure an ONU line profile.

OLT-1(config)#ont-lineprofile gpon profile-id 10 profile-name fttb(c)

OLT-1(config-gpon-lineprofile-10)#tcont 4 dba-profile-name fttb_dba

OLT-1(config-gpon-lineprofile-10)#gem add 11 eth tcont 4 cascade on

OLT-1(config-gpon-lineprofile-10)#gem add 12 eth tcont 4 cascade on

OLT-1(config-gpon-lineprofile-10)#gem add 13 eth tcont 4 cascade on

OLT-1(config-gpon-lineprofile-10)#gem mapping 11 0 vlan 8

OLT-1(config-gpon-lineprofile-10)#gem mapping 12 1 vlan 1001

OLT-1(config-gpon-lineprofile-10)#gem mapping 13 2 vlan 200

OLT-1(config-gpon-lineprofile-10)#commit

OLT-1(config-gpon-lineprofile-10)#quit

In this example, the default alarm profile is used and therefore the configuration of the alarm profile is not required.

Step-2: Add an ONU to an OLT.

=> Add an ONU offline.

OLT-1(config)#interface gpon 0/2

OLT-1(config-if-gpon-0/2)#ont add 1 ontid 1 sn-auth 32303131B39FD641 snmp ont-lineprofile-name fttb(c)

=>Confirm an automatically discovered ONU.

OLT-1(config)#interface gpon 0/2

OLT-1(config-if-gpon-0/2)#port 1 ont-auto-find enable

OLT-1(config-if-gpon-0/2)#display ont autofind 1

OLT-1(config-if-gpon-0/2)#ont confirm 1 ontid 1 sn-auth 32303131B39FD641 snmp ont-lineprofile-name fttb(c)

 Step-3: Check the ONU status.

After an ONU is added, run the display ont info command to query the current status of the ONU. Ensure that Config flag of the ONU is active, Run State is online, and Config state is normal.

OLT-1(config-if-gpon-0/2)#display ont info 1 1

OLT-1(config-if-gpon-0/2)#quit

Step-4: Configure the inband management VLAN and IP address of the OLT.

OLT-1(config)#vlan 8 smart

OLT-1(config)#port vlan 8 0/19 0

OLT-1(config)#vlan priority 8 6

OLT-1(config)#interface vlanif 8

OLT-1(config-if-vlanif8)#ip address 192.168.50.1 24

OLT-1(config-if-vlanif8)#quit

Step-5: Configure the inband management VLAN and IP address of the ONU.

OLT-1(config)#interface gpon 0/2

OLT-1(config-if-gpon-0/2)#ont ipconfig 1 1 static ip-address 192.168.50.2 mask 255.255.255.0 gateway 192.168.50.1 vlan 8

OLT-1(config-if-gpon-0/2)#quit

 Step-6: Configure an inband management service port.

OLT-1(config)#service-port 1 vlan 8 gpon 0/2/1 ont 1 gemport 11 multi-service user-vlan 8 rx-cttr 6 tx-cttr 6

 Step-7: Confirm that the management channel between the OLT and the ONU is available.

Step-8: Configure a channel for the Internet access service.

OLT-1(config)#vlan 100 smart

OLT-1(config)#vlan attrib 100 stacking

OLT-1(config)#port vlan 100 0/19 0

OLT-1(config)#service-port vlan 100 gpon 0/2/1 ont 1 gemport 12 multi-service user-vlan 1001 tag-transform default rx-cttr 6 tx-cttr 6

 Step-9: Configure a channel for the Voice service.

OLT-1(config)#vlan 200 smart

OLT-1(config)#port vlan 200 0/19 0

OLT-1(config)#traffic table ip index 9 cir off priority 5 priority-policy localsetting

OLT-1(config)#service-port vlan 200 gpon 0/2/1 ont 1 gemport 13 multi-service user-vlan 200 rx-cttr 9 tx-cttr 9

 Step-10: Configure a channel for the VoD service.

OLT-1(config)#vlan 300 smart

OLT-1(config)#port vlan 300 0/19 0

OLT-1(config)#traffic table ip index 10 cir off priority 4 priority-policy local-Setting

OLT-1(config)#service-port vlan 300 gpon 0/2/1 ont 1 gemport 14 multi-service user-vlan 300 rx-cttr 10 tx-cttr 10

 Step-11: Configure a channel for the multicast service.

OLT-1(config)#vlan 1000 smart

OLT-1(config)#port vlan 1000 0/19 0

OLT-1(config)#service-port vlan 1000 gpon 0/2/1 ont 1 gemport 14 multi-service user-vlan 1000 rx-cttr 10 tx-cttr 10

OLT-1(config)#btv

OLT-1(config-btv)#igmp cascade-port 0/2/1 ontid 1 gemport-index 14

OLT-1(config)#multicast-vlan 1000

OLT-1(config-mvlan1000)#igmp ipv6 version v2

OLT-1(config-mvlan1000)#igmp ipv6 mode proxy

Are you sure to change IGMP IPv6 mode?(y/n)[n]:y

OLT-1(config-mvlan1000)#igmp uplink-port 0/19/0

OLT-1(config-mvlan1000)#igmp program add batch ipv6 ff15:: to-ipv6 ff15::ffff source-ipv6 2000::1

 Step-12: Configure LAG for upstream ports.

Configure upstream ports 0/19/0 and 0/19/1 into an aggregation group. Each member port in the aggregation group allocates packets based on the source MAC address. The working mode is LACP static aggregation.

OLT-1(config)#link-aggregation 0/19 0-1 ingress workmode lacp-static

Step-13: (Optional) When PPPoE is adopted, enable forwarding the packets with PITP tag on the OLT equipment.

OLT-1(config)#pitp permit-forwarding service-port 101 enable

Step-14: (Optional) When IPoE is adopted, enable forwarding the packets with DHCP option on the OLT

equipment.

OLT-1(config)#dhcp-option82 permit-forwarding service-port 101 enable //For IPv4 packets

OLT-1(config)#dhcpv6-option permit-forwarding port 0/2/1 ontid 1 enable //For IPv6 packets

Step-15: Save the configuration data on the OLT.

OLT-1(config)#save

Step-16: Log in to and configure the ONU.

You can remote log in to the ONU from the OLT to perform the configuration. By default, the user name is root and the password is mduadmin.

NOTE:

The following steps are configured on the ONU side. 

Step-17: Configuration the HSI service on the ONU side.

NOTE:

This example creates one service port as an example. Each service port maps a user. When configuring another service port, map the corresponding SVLAN.

OLT-1(config)#vlan 1001-1016 smart

OLT-1(config)#port vlan 1001-1016 0/0 1

OLT-1(config)#traffic table ip index 8 cir 4096 priority 0 priority-policy localsetting

OLT-1(config)#serviceport 101 vlan 1001 eth 0/3/1 multi-service user-vlan untagged rx-cttr 8 tx-cttr 8

OLT-1(config)#service-port 101 vlan 1001 eth 0/3/1 multi-service user-vlan 10 rx-cttr 8 tx-cttr 8

 Step-18: (Optional) Configure the PITP function for PPPoE.

OLT-1(config)#raio-mode common pitp-pmode

OLT-1(config)#pitp enable pmode

 Step-19: (Optional) Configure the DHCP option function for IPoE.

OLT-1(config)#raio-mode common dhcp-option82 //For DHCPv4 packets

OLT-1(config)#dhcp option82 enable //For DHCPv4 packets

OLT-1(config)#raio-mode common dhcpv6-option //For DHCPv6 packets

OLT-1(config)#dhcpv6 option enable //For DHCPv6 packets

Step-20: Configure the voice service.

OLT-1(config)#vlan 200 smart

OLT-1(config)#port vlan 200 0/0 1

OLT-1(config)#interface vlanif 200

OLT-1(config-if-vlanif200)#ip address 17.10.10.10 24

OLT-1(config-if-vlanif200)#quit

OLT-1(config)#voip

OLT-1(config-voip)#ip address media 17.10.10.10 17.10.10.1

OLT-1(config-voip)#ip address signaling 17.10.10.10

OLT-1(config-voip)#quit

OLT-1(config)#ip route-static 200.200.200.0 24 17.10.10.1

OLT-1(config)#interface h248 0

Are you sure to add MG interface?(y/n)[n]:y

OLT-1(config-if-h248-0)#if-h248 attribute mgip 17.10.10.10 mgport 2944 code text transfer udp primary-mgc-ip1 200.200.200.200 primary-mgc-port 2944 mg-media-ip1 17.10.10.10 start-negotiate-version 1

OLT-1(config-if-h248-0)#reset coldstart

Are you sure to reset MG interface?(y/n)[n]:y

OLT-1(config-if-h248-0)#quit

OLT-1(config)#esl user

OLT-1(config-esl-user)#mgpstnuser batadd 0/3/0 0/3/23 0 terminalid 0 telno 83110001

OLT-1(config-esl-user)#mgpstnuser modify 0/3/0 priority cat2

OLT-1(config-esl-user)#quit

OLT-1(config)#pstnport

OLT-1(config-pstnport)#pstnport attribute batset 0/3/0 0/3/23 reverse-pole-pulse enable

OLT-1(config-pstnport)#quit

Step-21: Configure the VoD service.

Create VLAN 300 with the common attribute and add upstream port 0/0/1 to the VLAN.

OLT-1(config)#vlan 300 smart

OLT-1(config)#port vlan 300 0/0 1

Configure a traffic profile for the IPTV service.

OLT-1(config)#traffic table ip index 10 cir off priority 4 priority-policy localsetting

Configure a service flow for the VoD service. Configurations vary according to upstream interface types of HGWs. Assume that the user VLAN ID is 1 and the Ethernet port is 0/3/1. Add a service flow as follows:

OLT-1(config)#service-port 301 vlan 300 eth 0/3/1 multi-service user-vlan 1 rxcttr 10 tx-cttr 10

Assume that the VPI/VCI is 0/35 and the ADSL2+ port is 0/2/0. Add a service flow as follows:

OLT-1(config)#service-port 301 vlan 300 adsl vpi 0 vci 35 0/2/0 multi-service user-vlan untagged rx-cttr 10 tx-cttr 10

Assume that the VDSL2 path mode is PTM mode, port is 0/1/0, and packets from the user VLAN are untagged. Add a service flow as follows:

OLT-1(config)#service-port 301 vlan 300 vdsl mode ptm 0/1/0 multi-service uservlan untagged rx-cttr 10 tx-cttr 10

Step-22: Configure the multicast service.

OLT-1(config)#vlan 1000 smart

OLT-1(config)#port vlan 1000 0/0 1

OLT-1(config)#multicast-vlan 1000

OLT-1(config-mvlan1000)#igmp ipv6 version v2

OLT-1(config-mvlan1000)#igmp ipv6 mode proxy

Are you sure to change IGMP IPv6 mode?(y/n)[n]:y

OLT-1(config-mvlan1000)#igmp uplink-port 0/0/1

OLT-1(config-mvlan1000)#igmp program add batch ipv6 ff15:: to-ipv6 ff15::ffff source-ipv6 2000::1

OLT-1(config-mvlan1000)#quit

Configure a service flow for the multicast service. Configurations vary according to upstream interface types of HGWs. l If HGWs are connected to an ONU upstream through LANs, assume that the user VLAN ID is 43 and the Ethernet port is 0/3/1, and add a service flow as follows:

OLT-1(config)#service-port 401 vlan 1000 eth 0/3/1 multi-service user-vlan 43 rx-cttr 10 tx-cttr 10

=>If HGWs are connected to an ONU upstream in ADSL2+ mode, assume that the VPI/VCI is 0/35 and the ADSL2+ port is 0/2/0, and add a service flow as follows:

OLT-1(config)#service-port 401 vlan 1000 adsl vpi 0 vci 35 0/2/0 multi-service user-vlan untagged rx-cttr 10 tx-cttr 10

=>If HGWs are connected to an ONU upstream in VDSL2 mode, assume that the VDSL2 path mode is PTM mode, the user VLAN ID is 43, and the VDSL2 port is 0/1/0, and add a service flow as follows:

OLT-1(config)#service-port 401 vlan 1000 vdsl mode ptm 0/1/0 multi-service uservlan 43 rx-cttr 10 tx-cttr 10

OLT-1(config-mvlan1000)#btv

OLT-1(config-btv)#igmp user add service-port 401 no-auth

OLT-1(config-btv)#multicast-vlan 1000

OLT-1(config-mvlan1000)#igmp multicast-vlan member service-port 401

OLT-1(config-mvlan1000)#quit

Step-23: Save the configuration on the ONU side.

OLT-1(config)#save

***End***

Be the first to comment

Leave a Reply

Your email address will not be published.


*


For security, use of Google's reCAPTCHA service is required which is subject to the Google Privacy Policy and Terms of Use.

I agree to these terms.