ZTE ZXA10 MDU ONU F820 Data Service Configuration-ZTE

Please make sure that the network device works normally.

Please make sure that the VLAN is configured properly on uplink equipment.

Please make sure that the in-band NM IP address of the ZXA10 C220 is configured.

Please make sure that the GPON card works normally.

Please log in to the ZXA10 C220 through HyperTerminal or Telnet.

*****Configuration Notes*****

Note-1: Service VLAN:

VLAN ID: 100

Priority: 1

Note-2: Uplink port: 0/14/1

Note-3: GPON port: 0/5/1

Note-4: Bandwidth profile:

Profile name: T1–50M

Bandwidth type: Maximum (Type4)

Bandwidth: 50 Mbps

Note-5: ONU:

ONU ID: 1

ONU authentication mode: SN

ONU type: F820

ONU SN: ZTEG9000002B

Note-6: ONU in-band NM:

VLAN ID: 1000

Priority: 1

IP address: 10.67.1.11

Subnet mask: 255.255.255.0

Gateway: 10.67.1.254

Note-7: T-CONT:

T-CONT index: 1

T-CONT name: Tcont50M

Bandwidth profile: T1–50M

Alloc ID: Auto-allocate

Note-8: GEM port 1:

T-CONT index: 1

GEM Port index: 1

GEM Port name: NMport

Port ID: Auto-allocate

Note-9: GEM port 2:

T-CONT index: 1

GEM Port index: 2

GEM Port name: Gemport2

Port ID: Auto-allocate

Note-10: ONU NM service connection:

GEM port name: NM port

Bridge: 0/1

Uplink interface: 0/1/1

Connection type: bridge +dot1p

Note-11: ONU unicast service connection:

GEM port name: Gemport2

UNI: fei_0/1/1

Bridge: 0/1

Uplink interface: 0/1/2

Connection type: 802.1p +bridge

*****Configuration Steps*****

Task-1: Log in to the F820 through Hyper Teminal (username: zteolt1, password: abc123789).

Task-2: Configure GPON SN on the F820.

  1. Query card status.
  2. Enter global configuration mode and configure GPON SN.

⇒ ⇒ Reset GPON card (GPUA card) in slot 2 and wait for 1 minute.

Task-3: Configure F820 in-band NM.

  1. Enter VLAN interface configuration mode, configure in-band NM IP address.
  2. Configure in-band NM route.

Task-4: Configure service VLAN on the F820.

Task-5: Save configuration data.

Task-6: Configure F820 ONU type on the ZXA10 C220.

  1. Enter the global configuration mode.
  2. Enter PON configuration mode and configure ONU type.

Configure ONU port type.

Task-7: Register ONU.

  1. Query unconfigured ONU on the GPON-OLT port.
  2. Enter the GPON-OLT interface configuration mode.

⇒ Register ONU.

  1. Query ONU state.

Task-8: Configure bandwidth profile.

A bandwidth profile defines upstream bandwidth of a T-CONT.

  1. Enter the GPON configuration mode.
  2. Configure bandwidth profile.

Task-9: Configure T-CONT and GEM ports.

T-CONT (Transmission Container) is the minimum unit of upstream bandwidth scheduling which is identified by Alloc ID.

GEM port is the minimum unit of downstream traffic which is identified by port ID.

  1. Enter the GPON-ONU interface configuration mode.
  2. Create T-CONT.

⇒ Create GEM ports.

Task-10: Configure VLAN service port.

  1. Enter the GPON-ONU interface configuration mode.
  2. Configure port mode to hybrid.

⇒ Add port to in-band NM and service VLAN in tag mode.

Task-11: Configure VLAN uplink port.

  1. Enter the OLT uplink port configuration mode.
  2. Configure uplink port mode to hybrid.

⇒ Add uplink port to service VLAN in tag mode.

Task-12: Configure ONU NM service connection.

  1. Enter the ONU remote management mode.
  2. Configure the map between GEM port and uplink interface.

⇒ Configure VLAN filter mode on uplink interface.

  1. Configure VLAN filter entry on uplink interface.

Task-13: Configure ONU unicast service connection.

  1. Configure the map between GEM port and uplink interface.
  2. Configure VLAN filter mode on uplink interface.

⇒ Configure VLAN filter entry on uplink interface.

Task-14: Save configuration data.

Result: The PC connected to this ONU can access the Internet after the data service is configured successfully.

Configuration File>>

***END***

Be the first to comment

Leave a Reply

Your email address will not be published.


*


For security, use of Google's reCAPTCHA service is required which is subject to the Google Privacy Policy and Terms of Use.

I agree to these terms.